User Tools

Site Tools


usb_rotator_interface_4

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
Next revision Both sides next revision
usb_rotator_interface_4 [2021/08/01 12:17]
ok1hra [Steps of assembly]
usb_rotator_interface_4 [2021/12/27 14:16]
ok1hra [Steps of assembly]
Line 85: Line 85:
 The estimated difficulty of the assembly - for **moderately advanced solder maker.**\\ The estimated difficulty of the assembly - for **moderately advanced solder maker.**\\
   - Check all parts {{https://remoteqth.com/img/wiki-rot4-04.jpg}}\\ \\   - Check all parts {{https://remoteqth.com/img/wiki-rot4-04.jpg}}\\ \\
-  - Solder pinheader **P5, JP2, U1** and pinsocket 6x2 **P3** \\ **WARNING, do not solder P1!** {{https://remoteqth.com/img/wiki-rot4-05.jpg}}\\ \\+  - **First time** solder three connectors **P2,P3, P4** {{https://remoteqth.com/img/wiki-rot4-54.jpg}} \\ \\ 
 +  - Connect USB cable to Rotator interface and your PC, and check (device manager in windows) **that the USB converter has been recognized correctly.** Contact us if you have any problems and do not continue assembly. {{https://remoteqth.com/img/wiki-bd2-ftdi.png}} \\ \\ 
 +  - Solder pinheader **P5, JP2, U1** and pinsocket 6x2 **P3** \\ **WARNING, do not solder P1!**\\  Explanation: P1 use in factory for upload bootloader to CPU, therefore no further need. {{https://remoteqth.com/img/wiki-rot4-05.jpg}}\\ \\
   - Solder **S4** reset switch {{https://remoteqth.com/img/wiki-rot4-06.jpg}}\\ \\   - Solder **S4** reset switch {{https://remoteqth.com/img/wiki-rot4-06.jpg}}\\ \\
   - **Cut one of pin S4** switch nearest to S2 switch, see picture {{https://remoteqth.com/img/wiki-rot4-07.jpg}}\\ \\   - **Cut one of pin S4** switch nearest to S2 switch, see picture {{https://remoteqth.com/img/wiki-rot4-07.jpg}}\\ \\
Line 92: Line 94:
   - Put 3D print **LCD frame** {{https://remoteqth.com/img/wiki-rot4-10.jpg}}\\ \\   - Put 3D print **LCD frame** {{https://remoteqth.com/img/wiki-rot4-10.jpg}}\\ \\
   - Remove protective foil from LCD {{https://remoteqth.com/img/wiki-rot4-11.jpg}}\\ \\   - Remove protective foil from LCD {{https://remoteqth.com/img/wiki-rot4-11.jpg}}\\ \\
-  - Put on LCD to pinheader and **screw the M3x10 into the corner** of the plastic frame (without the use of a nut, the hole is conical) {{https://remoteqth.com/img/wiki-rot4-12.jpg}}\\ \\+  - Put on LCD to pinheader and **screw the M3x10 into the corner** of the plastic frame (without the use of a nut, the hole is conical) {{https://remoteqth.com/img/wiki-rot4-12.jpg}} \\ **NOTE:** if your kit contains an LCD with 2.5 mm holes, use a 3 to 3.2 mm drill bit to enlarge them (4x) {{https://remoteqth.com/img/wiki-rot4-33.jpg?300}}\\ \\
   - During solder LCD **press the frame and the LCD** so that there is no space between them {{https://remoteqth.com/img/wiki-rot4-13.jpg}}\\ \\   - During solder LCD **press the frame and the LCD** so that there is no space between them {{https://remoteqth.com/img/wiki-rot4-13.jpg}}\\ \\
   - Solder all 16 pins {{https://remoteqth.com/img/wiki-rot4-14.jpg}}\\ \\   - Solder all 16 pins {{https://remoteqth.com/img/wiki-rot4-14.jpg}}\\ \\
Line 105: Line 107:
   - Solder pinheader **JP3, JP1, P6 and P2** (cut to 6x2) {{https://remoteqth.com/img/wiki-rot4-21.jpg}}\\ \\   - Solder pinheader **JP3, JP1, P6 and P2** (cut to 6x2) {{https://remoteqth.com/img/wiki-rot4-21.jpg}}\\ \\
   - Solder **C28 and C29 capacitor marked 472** {{https://remoteqth.com/img/wiki-rot4-22.jpg}}\\ \\   - Solder **C28 and C29 capacitor marked 472** {{https://remoteqth.com/img/wiki-rot4-22.jpg}}\\ \\
-  - Solder **V1, V2, V3, V4 varistors marked 180K07D** From September 2021 change of type from blue to red +  - Solder **V1, V2, V3, V4 varistors marked 180K07D** \\ {{https://remoteqth.com/img/wiki-rot4-23.jpg}}\\ {{https://remoteqth.com/img/wiki-rot4-53.jpg?500}}\\ (From September 2021 change of type from blue to red) \\ \\
-{{https://remoteqth.com/img/wiki-rot4-53.jpg}}\\ +
-{{https://remoteqth.com/img/wiki-rot4-23.jpg}}\\ \\+
   - Solder **P4 USB-B** connector {{https://remoteqth.com/img/wiki-rot4-24.jpg}}\\ \\   - Solder **P4 USB-B** connector {{https://remoteqth.com/img/wiki-rot4-24.jpg}}\\ \\
   - Solder polyfuse **F1** {{https://remoteqth.com/img/wiki-rot4-25.jpg}}\\ \\   - Solder polyfuse **F1** {{https://remoteqth.com/img/wiki-rot4-25.jpg}}\\ \\
Line 310: Line 310:
   - Open serial monitor in Arduino CLI (Ctrl+Shift+M)   - Open serial monitor in Arduino CLI (Ctrl+Shift+M)
   - Set Carriage return and 9600 baud   - Set Carriage return and 9600 baud
 +  - Previous start point and range also available preset [[https://github.com/ok1hra/k3ng_rotator_controller/blob/master/k3ng_rotator_controller/rotator_settings.h#L12|via CLI]]<code>
 +\Ix[x][x] - set az starting point
 +\I - display the current az starting point
 +\Jx[x][x] - set az rotation capability
 +\J - display the current az rotation capability
 +\Q - Save settings in the EEPROM and restart</code>
   - For callibration voltage to preset azimuth range in firmware use<code>   - For callibration voltage to preset azimuth range in firmware use<code>
 O  - Azimuth offset calibration O  - Azimuth offset calibration
usb_rotator_interface_4.txt · Last modified: 2022/02/17 23:23 by ok1hra