User Tools

Site Tools


3d_print_wx_station

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
Last revision Both sides next revision
3d_print_wx_station [2021/01/29 19:27]
ok1hra [Passive thermometer sun shield]
3d_print_wx_station [2021/05/15 22:44]
ok1hra
Line 2: Line 2:
 [[https://remoteqth.com/3d-wx-station.php|Web page]] \\ [[https://remoteqth.com/3d-wx-station.php|Web page]] \\
 \\ \\
-**With propagation to APRS** - [[https://aprs.fi/weather/a/OK1HRA-6|OK1HRA-6]] [[https://aprs.fi/weather/a/ok1kpa-6|OK1KPA-6]]\\+**Instaled stations** - [[https://aprs.fi/weather/a/OK1HRA-6|OK1HRA-6]] [[https://aprs.fi/weather/a/ok1kpa-6|OK1KPA-6]] [[http://hrochovo.cz/weewx/|OK1IRG weewx]]\\
 \\ \\
 {{youtube>6wNjkw3fjq8?large}} {{youtube>6wNjkw3fjq8?large}}
Line 80: Line 80:
   - After firmware upload you can upload next version of the firmware via IP, if you computer in same network. In Arduino IDE shows another choice Network ports \\ {{https://remoteqth.com/img/3d-wx-station-10.png?200}}   - After firmware upload you can upload next version of the firmware via IP, if you computer in same network. In Arduino IDE shows another choice Network ports \\ {{https://remoteqth.com/img/3d-wx-station-10.png?200}}
   - password for OTA upload is //remoteqth//   - password for OTA upload is //remoteqth//
 +  - After first upload also available upload binary via web \\ {{https://remoteqth.com/img/3d-wx-station-54.png?200}} \\ - binary available on [[https://github.com/ok1hra/3D-print-WX-station/releases|release page]] \\ - web form find on http port 82 on WX station IP and /update foleder **[WXstationIP]:82/update**
  
 ---- ----
Line 129: Line 130:
 | **L** | change location name, or callsign with ssid if enable APRS | | **L** | change location name, or callsign with ssid if enable APRS |
 | **A** | enable/disable upload to hamradio APRS network (requires a valid license) | | **A** | enable/disable upload to hamradio APRS network (requires a valid license) |
-| **s** | enable/disable external temperature sensor DS18B20 \\ connected to P4 by this schematics/picture \\ {{https://remoteqth.com/img/wiki-wx-station-01.png?x300}} \\ **NOTICE** \\ If use external temperature sensor DS18B20, \\ **must add 4k7 pull-up rezistor** \\ between +3,3V and data (pin 1 and pin3 on P4 connector) \\ {{https://remoteqth.com/img/wiki-wx-station-02.jpg?x500}} |+| **s** | enable/disable external temperature sensor DS18B20 \\ connected to P4 by this schematics/picture \\ {{https://remoteqth.com/img/wiki-wx-station-01.png?x300}} \\ **NOTICE** \\ If use external temperature sensor DS18B20, \\ **must add 4k7 pull-up rezistor** \\ between +3,3V and data (pin 1 and pin3 on P4 connector) \\ {{https://remoteqth.com/img/wiki-wx-station-02.jpg?x500}} \\ \\ How to build [[3d_print_wx_station#passive_thermometer_sun_shield|passive thermometer sun shield]] |
 | **q** | disconect telnet, also show login verified IP address | | **q** | disconect telnet, also show login verified IP address |
 | **Q** | disconect telnet with erase verified IP addres - will be required key in the next time you log in | | **Q** | disconect telnet with erase verified IP addres - will be required key in the next time you log in |
Line 176: Line 177:
   - With press the pliers to put on{{https://remoteqth.com/img/wiki-wx-station-25.jpg}} \\ \\   - With press the pliers to put on{{https://remoteqth.com/img/wiki-wx-station-25.jpg}} \\ \\
   - Screw in M3x10 to printed **parts number 14**{{https://remoteqth.com/img/wiki-wx-station-26.jpg}} \\ \\   - Screw in M3x10 to printed **parts number 14**{{https://remoteqth.com/img/wiki-wx-station-26.jpg}} \\ \\
-  - fit the azimuth blade and screw it on stainless steel threaded rod M6x125mm on, **so as to keep them horizontally balanced** - M6 nuts can be screwed in for balancing{{https://remoteqth.com/img/wiki-wx-station-27.jpg}} \\ \\+  - fit the azimuth blade and screw it on stainless steel threaded rod M6x125mm on, **so as to keep them horizontally balanced** - M6 nuts can be screwed in for balancing{{https://remoteqth.com/img/wiki-wx-station-27.png}} \\ \\
   - Fit part number 14 on part number 12 so that the locking **screw is against the bottom hole**{{https://remoteqth.com/img/wiki-wx-station-28.jpg}} \\ \\   - Fit part number 14 on part number 12 so that the locking **screw is against the bottom hole**{{https://remoteqth.com/img/wiki-wx-station-28.jpg}} \\ \\
   - Install the three anemometer blades{{https://remoteqth.com/img/wiki-wx-station-29.jpg}} \\ \\   - Install the three anemometer blades{{https://remoteqth.com/img/wiki-wx-station-29.jpg}} \\ \\
Line 187: Line 188:
  
 ===== Passive thermometer sun shield ===== ===== Passive thermometer sun shield =====
 +{{https://remoteqth.com/img/wiki-wx-station-54.png?420}} {{https://remoteqth.com/img/wiki-wx-station-55.png?420}} \\
 +This part needed for accurate measure of temperature.
  
-This part need for acurrate measure of temperature. +  * First step **measure** mouting pipe diameter \\ {{ https://remoteqth.com/img/wiki-wx-station-40.jpg?400}} 
- +  * [[https://remoteqth.com/3d-wx-station.php#download|Download 3d models]] \\
-  * First step **measure** mouting pipe diameter \\ {{ https://remoteqth.com/img/wiki-wx-station-40.jpg?400}} \\+
   * Now open **source code** in OpenScad and change line <code>MOUNTDIA  =  42;</code>   * Now open **source code** in OpenScad and change line <code>MOUNTDIA  =  42;</code>
-  * Change the parameter gradually from 1 to 3 <code>Part  =  1;</code> then press F6 and F7 for .STL export this part. Other parts not depend to mounting pipe diameter. \\ +  * Change the parameter gradually from 1 to 3 <code>Part  =  1;</code> then press F6 and F7 for .STL export this part. Other parts not depend to mounting pipe diameter. 
-  * After complete all STL parts you can **start 3D printing with WHITE PETG** filament. Sun-shield part nr 4 you print four times. \\ {{https://remoteqth.com/img/wiki-wx-station-53.png}} \\+  * After complete all STL parts you can **start 3D printing with WHITE PETG** filament. Sun-shield part nr 4 you print four times. \\ {{https://remoteqth.com/img/wiki-wx-station-53.png}}
  
-| M3 x10 mm | 18x | +| M3 x10 mm |  18x | 
-| M3 x 20mm | 3x | +| M3 x 20mm |  3x | 
-| Outdoor DS18B20 temperature sensor | 1x | +| Outdoor DS18B20 temperature sensor |  1x | 
-| Plastic binder | 5x |+| Plastic binder |  5x |
  
-  * **Check all parts** \\ {{https://remoteqth.com/img/wiki-wx-station-41.jpg}} \\ +  * **Check all parts** \\ {{https://remoteqth.com/img/wiki-wx-station-41.jpg}} \\ \\ 
-  * **Mount three screw M3x10mm** for join part 1 and 2 \\ {{https://remoteqth.com/img/wiki-wx-station-42.jpg?420}} +  * **Mount three screw M3x10mm** for join part 1 and 2 \\ {{https://remoteqth.com/img/wiki-wx-station-42.jpg?420}} \\ \\ 
-  * Plug **thermistor** to center part 3 \\ {{https://remoteqth.com/img/wiki-wx-station-43.jpg?420}} {{https://remoteqth.com/img/wiki-wx-station-44.jpg?420}} \\ +  * Plug **thermistor** to center part 3 \\ {{https://remoteqth.com/img/wiki-wx-station-43.jpg?420}} {{https://remoteqth.com/img/wiki-wx-station-44.jpg?420}} \\ \\ 
-  * **Mount three screw M3x10mm for join every floor** \\ {{https://remoteqth.com/img/wiki-wx-station-45.jpg?420}} {{https://remoteqth.com/img/wiki-wx-station-46.jpg?420}} \\ {{https://remoteqth.com/img/wiki-wx-station-47.jpg?420}} {{https://remoteqth.com/img/wiki-wx-station-48.jpg?420}} \\ {{https://remoteqth.com/img/wiki-wx-station-49.jpg?420}} {{https://remoteqth.com/img/wiki-wx-station-50.jpg?420}} \\ +  * **Mount three screw M3x10mm for join every floor** \\ {{https://remoteqth.com/img/wiki-wx-station-45.jpg?420}} {{https://remoteqth.com/img/wiki-wx-station-46.jpg?420}} \\ {{https://remoteqth.com/img/wiki-wx-station-47.jpg?420}} {{https://remoteqth.com/img/wiki-wx-station-48.jpg?420}} \\ {{https://remoteqth.com/img/wiki-wx-station-49.jpg?420}} {{https://remoteqth.com/img/wiki-wx-station-50.jpg?420}}  \\ \\ 
-  * {{https://remoteqth.com/img/wiki-wx-station-51.jpg}} +  * For Mount bottom grid with M3x20mm \\ {{https://remoteqth.com/img/wiki-wx-station-51.jpg}} \\ \\ 
-  * {{https://remoteqth.com/img/wiki-wx-station-52.jpg}}+  * Final mounting to pipe \\ {{https://remoteqth.com/img/wiki-wx-station-52.jpg}} \\ \\ 
 +  * [[3d_print_wx_station#how_command_are_available|How connect thermistor to meteostation board]]
  
 \\ \\
 ---- ----
- 
- 
  
 ===== Instalation ===== ===== Instalation =====
3d_print_wx_station.txt · Last modified: 2022/02/08 14:19 by ok1hra