Differences

This shows you the differences between two versions of the page.

--- 3d_print_wx_station [2021/01/29 18:25] – [Passive thermometer sun shield] ok1hra
+++ 3d_print_wx_station [2021/05/15 20:44] – ok1hra
@@ Line 2: / Line 2: @@
 [[https://remoteqth.com/3d-wx-station.php|Web page]] \\
 \\
-**With propagation to APRS** - [[https://aprs.fi/weather/a/OK1HRA-6|OK1HRA-6]] [[https://aprs.fi/weather/a/ok1kpa-6|OK1KPA-6]]\\
+**Instaled stations** - [[https://aprs.fi/weather/a/OK1HRA-6|OK1HRA-6]] [[https://aprs.fi/weather/a/ok1kpa-6|OK1KPA-6]] [[http://hrochovo.cz/weewx/|OK1IRG weewx]]\\
 \\
 {{youtube>6wNjkw3fjq8?large}}
@@ Line 80: / Line 80: @@
   - After firmware upload you can upload next version of the firmware via IP, if you computer in same network. In Arduino IDE shows another choice Network ports \\ {{https://remoteqth.com/img/3d-wx-station-10.png?200}}
   - password for OTA upload is //remoteqth//
+  - After first upload also available upload binary via web \\ {{https://remoteqth.com/img/3d-wx-station-54.png?200}} \\ - binary available on [[https://github.com/ok1hra/3D-print-WX-station/releases|release page]] \\ - web form find on http port 82 on WX station IP and /update foleder **[WXstationIP]:82/update**
 ----
@@ Line 129: / Line 130: @@
 | **L** | change location name, or callsign with ssid if enable APRS |
 | **A** | enable/disable upload to hamradio APRS network (requires a valid license) |
-| **s** | enable/disable external temperature sensor DS18B20 \\ connected to P4 by this schematics/picture \\ {{https://remoteqth.com/img/wiki-wx-station-01.png?x300}} \\ **NOTICE** \\ If use external temperature sensor DS18B20, \\ **must add 4k7 pull-up rezistor** \\ between +3,3V and data (pin 1 and pin3 on P4 connector) \\ {{https://remoteqth.com/img/wiki-wx-station-02.jpg?x500}} |
+| **s** | enable/disable external temperature sensor DS18B20 \\ connected to P4 by this schematics/picture \\ {{https://remoteqth.com/img/wiki-wx-station-01.png?x300}} \\ **NOTICE** \\ If use external temperature sensor DS18B20, \\ **must add 4k7 pull-up rezistor** \\ between +3,3V and data (pin 1 and pin3 on P4 connector) \\ {{https://remoteqth.com/img/wiki-wx-station-02.jpg?x500}} \\ \\ How to build [[3d_print_wx_station#passive_thermometer_sun_shield|passive thermometer sun shield]] |
 | **q** | disconect telnet, also show login verified IP address |
 | **Q** | disconect telnet with erase verified IP addres - will be required key in the next time you log in |
@@ Line 176: / Line 177: @@
   - With press the pliers to put on{{https://remoteqth.com/img/wiki-wx-station-25.jpg}} \\ \\
   - Screw in M3x10 to printed **parts number 14**{{https://remoteqth.com/img/wiki-wx-station-26.jpg}} \\ \\
-  - fit the azimuth blade and screw it on stainless steel threaded rod M6x125mm on, **so as to keep them horizontally balanced** - M6 nuts can be screwed in for balancing{{https://remoteqth.com/img/wiki-wx-station-27.jpg}} \\ \\
+  - fit the azimuth blade and screw it on stainless steel threaded rod M6x125mm on, **so as to keep them horizontally balanced** - M6 nuts can be screwed in for balancing{{https://remoteqth.com/img/wiki-wx-station-27.png}} \\ \\
   - Fit part number 14 on part number 12 so that the locking **screw is against the bottom hole**{{https://remoteqth.com/img/wiki-wx-station-28.jpg}} \\ \\
   - Install the three anemometer blades{{https://remoteqth.com/img/wiki-wx-station-29.jpg}} \\ \\
@@ Line 187: / Line 188: @@
 ===== Passive thermometer sun shield =====
+{{https://remoteqth.com/img/wiki-wx-station-54.png?420}} {{https://remoteqth.com/img/wiki-wx-station-55.png?420}} \\
+This part needed for accurate measure of temperature.
-This part need for acurrate measure of temperature.
+  * First step **measure** mouting pipe diameter \\ {{ https://remoteqth.com/img/wiki-wx-station-40.jpg?400}}
+  * [[https://remoteqth.com/3d-wx-station.php#download|Download 3d models]] \\
-  * First step **measure** mouting pipe diameter \\ {{ https://remoteqth.com/img/wiki-wx-station-40.jpg?400}} \\
   * Now open **source code** in OpenScad and change line <code>MOUNTDIA  =  42;</code>
-  * Change the parameter gradually from 1 to 3 <code>Part  =  1;</code> then press F6 and F7 for .STL export this part. Other parts not depend to mounting pipe diameter. \\
+  * Change the parameter gradually from 1 to 3 <code>Part  =  1;</code> then press F6 and F7 for .STL export this part. Other parts not depend to mounting pipe diameter.
-  * After complete all STL parts you can **start 3D printing with WHITE PETG** filament. Sun-shield part nr 4 you print four times. \\ {{https://remoteqth.com/img/wiki-wx-station-53.png}} \\
+  * After complete all STL parts you can **start 3D printing with WHITE PETG** filament. Sun-shield part nr 4 you print four times. \\ {{https://remoteqth.com/img/wiki-wx-station-53.png}}
-| M3 x10 mm | 18x |
+| M3 x10 mm |  18x |
-| M3 x 20mm | 3x |
+| M3 x 20mm |  3x |
-| Outdoor DS18B20 temperature sensor | 1x |
+| Outdoor DS18B20 temperature sensor |  1x |
-| Plastic binder | 5x |
+| Plastic binder |  5x |
-  * Check all parts \\ {{https://remoteqth.com/img/wiki-wx-station-41.jpg}} \\
-  * Mount three screw M3x10mm for join part 1 and 2 \\ {{https://remoteqth.com/img/wiki-wx-station-42.jpg?420}}
+  * **Check all parts** \\ {{https://remoteqth.com/img/wiki-wx-station-41.jpg}} \\ \\
-  * Plug thermistor to center part 3 \\ {{https://remoteqth.com/img/wiki-wx-station-43.jpg?420}} {{https://remoteqth.com/img/wiki-wx-station-44.jpg?420}} \\
+  * **Mount three screw M3x10mm** for join part 1 and 2 \\ {{https://remoteqth.com/img/wiki-wx-station-42.jpg?420}} \\ \\
-  * Mount three screw M3x10mm for join every floor \\ {{https://remoteqth.com/img/wiki-wx-station-45.jpg?420}} {{https://remoteqth.com/img/wiki-wx-station-46.jpg}} \\ {{https://remoteqth.com/img/wiki-wx-station-47.jpg?420}} {{https://remoteqth.com/img/wiki-wx-station-48.jpg?420}} \\ {{https://remoteqth.com/img/wiki-wx-station-49.jpg?420}} {{https://remoteqth.com/img/wiki-wx-station-50.jpg?420}} \\
+  * Plug **thermistor** to center part 3 \\ {{https://remoteqth.com/img/wiki-wx-station-43.jpg?420}} {{https://remoteqth.com/img/wiki-wx-station-44.jpg?420}} \\ \\
-  * {{https://remoteqth.com/img/wiki-wx-station-51.jpg}}
+  * **Mount three screw M3x10mm for join every floor** \\ {{https://remoteqth.com/img/wiki-wx-station-45.jpg?420}} {{https://remoteqth.com/img/wiki-wx-station-46.jpg?420}} \\ {{https://remoteqth.com/img/wiki-wx-station-47.jpg?420}} {{https://remoteqth.com/img/wiki-wx-station-48.jpg?420}} \\ {{https://remoteqth.com/img/wiki-wx-station-49.jpg?420}} {{https://remoteqth.com/img/wiki-wx-station-50.jpg?420}}  \\ \\
-  * {{https://remoteqth.com/img/wiki-wx-station-52.jpg}}
+  * For Mount bottom grid with M3x20mm \\ {{https://remoteqth.com/img/wiki-wx-station-51.jpg}} \\ \\
+  * Final mounting to pipe \\ {{https://remoteqth.com/img/wiki-wx-station-52.jpg}} \\ \\
+  * [[3d_print_wx_station#how_command_are_available|How connect thermistor to meteostation board]]
 \\
 ----
 ===== Instalation =====